Now adjust the distance of the second-string saddle back from the first saddle, using the gauge of the second string as a measurement. Set the pickup selector switch in the middle position, and turn the volume and tone controls to their maximum settings. Proceed with the fifth and sixth saddles with the same method used for strings two and three.Lubricating all of the contact points of a string's travel may be one of the most important elements in ensuring tuning stability during tremolo use and in reducing string breakage.The main cause of string breakage is moisture collection at the point of contact on the bridge saddle. "First, remove the tremolo back cover. If you prefer a bridge flush to the body, adjust spring tension to equal string tension, while the bridge rests on the body (you may want to put an extra 1/2 turn to each claw screw to ensure that the bridge remains flush to the body during string bends). If the neck is too concave (action too high), turn the truss rod nut clockwise to remove excess relief. Start by loading all the strings through the bridge and then loading them onto the keys as follows:If your tuning keys have a screw on the end of the button, check the tightness of the screw. Therefore, when you buy one, you get three, which you can use for your strat neck, middle and bridge. 2003 Fender Classic 50s 60s 70s Stratocaster Alnico Neck Pickup. Move the third saddle back from the second saddle using the gauge of the third string as a measurement. If the neck is too concave (action too high), turn the truss rod nut clockwise to remove excess relief. The design allows the string to travel freely in the bridge block channel during tremolo use and return afterwards to its original position, seated snugly in the bridge block. Since it was first introduced in 1954, the Fender Strat has become the favored axe of countless slingers who want a tone that's bright and cutting - which of course, is what single-coil pickups do best. With a feeler gauge, check the gap between the bottom of the string and the top of the 8th fret—Adjustment at headstock (allen wrench): Sight down the edge of the fingerboard from behind the headstock, looking toward the body of the instrument.
Check your tuning. If the neck is too convex (strings too close to the fingerboard), turn the truss rod nut counter-clockwise to allow the string tension to pull more relief into the neck. After you've played a few riffs and done a few dive-bombs, you can then do your final tuning. Check tuning. If you plan to change string gauges, you may need to adjust the specs somewhat to compensate for the changes in string sizes. String trees are another point of contact and should also be lubricated; a small amount of lip balm applied with a toothpick works well.There are two different styles of truss rod found on Fender instruments—"standard" and "bi-flex" truss rods.Most Fender guitars and basses are equipped with a standard truss rod (of which there are in turn two types: one that adjusts at the neck heel and one that adjusts at the headstock; both operate on the same principle). From rhythm and blues to country and rock, there's a single coil pickup to match every musical genre in this section. It replaces the need for a shim by using a hex screw against a plate installed in the butt end of the neck. Depress all the strings at the last fret. Remember, guitars are tempered instruments! When transporting or storing your guitar, even for short periods, avoid leaving it anyplace you wouldn't feel comfortable yourself. restrictions. Or, if you're after a sound that adds a bit more midrange and increased sustain, go with the EMG EMG-SA Alnico Single Coil Active Pickup. Delivering killer overdrive while still retaining the high-end output that a single-coil pickup is known for, this pickup is incredibly versatile.
Using a 6" (150 mm) ruler, measure the distance from the bottom of the first and sixth strings to the top of the pole piece. Check your tuning, then re-check the gap with the feeler gauge and re-adjust as needed.Players with a light touch can get away with lower action; others need higher action to avoid rattles. You can preset the basic intonation of your guitar by taking a tape measure and measuring from the inside of the nut to the center of the 12th fret (the fret wire itself; not the fingerboard). Strings that have lost their integrity (worn where pressed against the fret) or have become oxidized, rusty and dirty will not return to pitch properly. The pitch of the neck on your guitar has been preset at the factory and in most cases will not need to be adjusted.Set too high, pickups can cause myriad inexplicable phenomena. Then tighten the two outside screws back down until they're flush with the top of the bridge plate. Fender 5-Way Selector Switch 4.8 out of 5 stars 368. If you find any of these, you should change your strings.No matter what gauge of strings you use, for the best tuning stability we recommend using Fender Bullet® strings. Follow the measurement guidelines in the chart below as starting points. Fender features three pieces of these pickups in a set. Using a 6" (150 mm) ruler, measure the distance between bottom of strings and top of the 17th fret. With that in mind, you can easily imagine what the Fender Customer Shop '54 Strat Pickup Set Of 3 sounds like based on its title alone. If you change the Ship-To country, some or A shim is placed in the neck pocket, underneath the butt end of the neck. Affix a capo at the first fret and depress the sixth string at the last fret. It also just happens to be the pickup-of-choice amongst many iconic guitarists like David Gilmour of Pink Floyd and Steve Lukather of Toto.
Fender Vintage Strat Pickup Cover Set, Black 4.4 out of 5 stars 97. And these are just two of many top-selling pickups that make up this catalog. Experiment with the height until the desired sound and feel is achieved.Shimming is a procedure used to adjust the pitch of the neck in relation to the body. Then loosen all six screws located at the front edge of the bridge plate, raising them so that they all measure approximately 1/16" (1.6 mm) above the top of the bridge plate.